Dedicated Subsystem WorkbenchPlatform Gen: 2018–2024

2023 Husqvarna Svartpilen 401 / Vitpilen 401 Charging System, Stator AC Output & Battery Health

Stator 3-phase AC voltage at 5,000 RPM, coil resistance, regulated DC voltage, battery code ETZ-9 (12V 8Ah AGM), CCA rating, and multimeter charging diagnostic steps for 2023 Husqvarna Svartpilen 401 / Vitpilen 401.

Gen 2018–2024

Factory Platform Compatibility: All workshop fluid capacities, maintenance milestones, torque specifications, and consumables on this specification sheet are factory-identical across model years 2018 through 2024.

Select Model Year:(Active: 2023)

2018 2019 2020 2021 2022 2023 2024

Engine

373cc

Drive

520

Cooling

Not Available

3-Phase Charging System & Battery Diagnostic Flowchart

Yuasa & OEM Standards

Multimeter troubleshooting protocols, cold cranking amps (CCA) ratings, 3-phase stator AC outputs, and regulator-rectifier health verification.

Shop ETZ-9 (12V 8Ah AGM) Batteries

OEM Battery Code

ETZ-9 (12V 8Ah AGM)

Cold Cranking Rating

Not Available

Capacity (10HR Rate)

Not Available

Regulated Output Spec

Key-OFF Parasitic Limit

Enter Multimeter DC Voltage Reading

V DC

Multimeter Test Diagnosis

Enter your multimeter terminal reading on the left to view instant diagnostic interpretations and recommended workshop actions.

OEM Factory AGM BatteryOEM Replacement

Dimensions: • Weight: Not Available. Pre-filled absorbed glass mat technology engineered for heavy vibration resistance.

Lithium LiFePO4 UpgradeUp to 70% Lighter

Features built-in RE-START jump starting reserve. Never stranded by dead lights: press the restart button on the top terminal to crank the motorcycle without jumper cables.

Smart Maintainer SpecBattery Life Extension

Standard Charge Rate: . Automated desulfation & float maintenance ensures full capacity retention during off-season winter storage.

Recommended Parts: •

Shop Smart Battery Chargers Find Direct-Fit Batteries

Husqvarna Diagnostic Fault Codes & Multimeter Bench Testing

FI & OBD2 Decoder

Authentic factory ECU fault codes, sensor resistance specifications, and harness pinout troubleshooting.

Launch Full Husqvarna DTC Engine→

Code P0105Manifold Absolute Pressure (MAP)

MAP sensor electrical circuit malfunction / range error.

Test: Verify 5.0V VRef and 2.5-3.0V signal key-on engine-off.

Code P0115Engine Coolant Temp (ECT)

ECT sensor circuit open, short, or out of plausible range.

Test: Measure NTC thermistor: ~2.5 kΩ at 20°C, 300 Ω at 80°C.

Code P0335Crankshaft Position Sensor (CKP)

CKP sensor electrical circuit or missing pulse teeth.

Test: Measure VR magnetic pickup coil resistance (typically 200-600 Ω).

Looking for other error codes, sensor pinouts, or OBD2/Euro 5 codes?

View All 68 Multi-Brand Diagnostic Trouble Codes →

Official NHTSA Safety Recalls & Technical Bulletins

0 Open Campaigns (Clean)

U.S. Department of Transportation compliance database (Title 49 U.S.C. Chapter 301).

Verify VIN on NHTSA.gov

No Active Federal Safety Recalls Reported

The U.S. DOT National Highway Traffic Safety Administration (NHTSA) records zero open safety recall campaigns for the 2023 Husqvarna Svartpilen 401 / Vitpilen 401 platform. Always check your individual 17-digit VIN at an authorized dealership or via NHTSA.gov for individual recall completions.

OEM Workshop Archives

Official Factory Service Bulletins & Field Updates

1 Documented Bulletin

Bulletin #KTM-25V598Safety Recall KTB2606 / HTB2603: Sealed E-Throttle Twist Grip Assembly & Adaptation Reset

Source: KTM_Recall25V598_RCRIT-25V598-9541.pdf

Mandated Torques:E-Throttle Housing Clamp Screws (2x M4): 3.5 N·m (31 in-lb)Handlebar End Weight Screw (M6): 20 N·m (15 lb-ft)Handlebar Switchgear Screws (M4): 2.0 N·m (18 in-lb)Front Brake Master Cylinder Clamp (M6): 5 N·m (44 in-lb)

Consumable Specs:N/A

Genuine Part Numbers:Exchange Throttle Cmpl. (390 Adv / Duke / 401) (95802010044)Exchange Switch Control RH (RC 390) (94811074000)EJOT PT Screw K40×12 (0081040121)Handlebar Grip Right (90102021000)

NHTSA Recall 25V-598 & 26V-196Bulletins KTB2606 & HTB2603