Dedicated Subsystem WorkbenchPlatform Gen: 2007–2016
2015 Harley Davidson Twin Cam 96 / 103 (Dyna / Softail / Touring) Charging System, Stator AC Output & Battery Health
Stator 3-phase AC voltage at 5,000 RPM, coil resistance, regulated DC voltage, battery code YTX20HL-BS (Dyna/Softail) / YIX30L-BS (Touring), CCA rating, and multimeter charging diagnostic steps for 2015 Harley Davidson Twin Cam 96 / 103 (Dyna / Softail / Touring).
Gen 2007–2016
Factory Platform Compatibility: All workshop fluid capacities, maintenance milestones, torque specifications, and consumables on this specification sheet are factory-identical across model years 2007 through 2016.
SPECS-TO-CART BUNDLESFactory Direct-Fit Maintenance Bundles Available
1-Click verified Motul engine oil service kits, race filters, spark plugs, and brake fluid pre-measured for this 2015 Harley Davidson Twin Cam 96 / 103 (Dyna / Softail / Touring).
Select Model Year:(Active: 2015)
10 Production Years (2007–2016)
Suggested Items3 Verified Workshop Consumables Available for this Job
View Suggested Items ↓3-Phase Charging System & Battery Diagnostic Flowchart
Yuasa & OEM StandardsMultimeter troubleshooting protocols, cold cranking amps (CCA) ratings, 3-phase stator AC outputs, and regulator-rectifier health verification.
OEM Battery Code
YTX20HL-BS (Dyna/Softail) / YIX30L-BS (Touring) (VRLA / Heavy-Duty AGM (Reversed Polarity))
Cold Cranking Rating
385 CCA
Capacity (10HR Rate)
28 Ah (12V)
Regulated Output Spec
14.2 - 14.8 V DC at 3,000 RPM
Key-OFF Parasitic Limit
< 3.0 mA (Security BCM / TSSM armed)
V DC
Multimeter Test Diagnosis
Enter your multimeter terminal reading on the left to view instant diagnostic interpretations and recommended workshop actions.
OEM Factory AGM BatteryOEM Replacement
Yuasa YIX30L-BS Factory Activated High Performance AGM Battery
Dimensions: 166 L × 126 W × 175 H mm • Weight: 21.8 lbs (9.9 kg). Pre-filled absorbed glass mat technology engineered for heavy vibration resistance.
Lithium LiFePO4 UpgradeUp to 70% Lighter
Antigravity ATX-30-HD Re-Start (880 CCA)
Features built-in RE-START jump starting reserve. Never stranded by dead lights: press the restart button on the top terminal to crank the motorcycle without jumper cables.
Smart Maintainer SpecBattery Life Extension
12V AGM / Float 1.25A
Standard Charge Rate: 3.0A (Max 5.0A). Automated desulfation & float maintenance ensures full capacity retention during off-season winter storage.
Recommended Parts: Yuasa YIX30L-BS Factory Activated High Performance AGM Battery • Battery Tender Plus 1.25A 12V Charger
IGNITION ENGINEERING, HEAT-RANGES & COMBUSTION DIAGNOSTICS
OEM Spark Plugs • Heat-Range Dissipation • Coil Resistance • Visual Combustion Reading Matrix
FACTORY CERTIFIED SPECIFICATIONS
Factory Standard Plug
HD 6R12
2
Electrode Spark Gap
0.97 - 1.09 mm (0.038 - 0.043 in)
12 mm × 1.25 • 19.0 mm (3/4 in) mm Reach
Hex Drive & Socket Spec
5/8 in (16 mm)
Use magnetic rubber-insert thin socket
Tightening Torque (NM)
20 N·m
1/2 turn after gasket contact
Stick Coil Resistances
Pri: 0.5 - 0.7 Ω (Single Fire Delphi EFI Coil)
Sec: 5,500 - 7,500 Ω across secondary towers
Service & Replacement
Inspect: 5,000 mi (8,000 km)
Replace: 10,000 mi (16,000 km)
SPARK PLUG HEAT-RANGE & METALLURGY SELECTOR
Compare OEM standard, fine-wire precious metals, and ambient/duty cycle thermal dissipation paths
Verified Part Specification
HD 6R12
Metallurgy & Center Tip Architecture
Copper Core / Solid Nickel Alloy Ground Electrode
Thermal Dissipation Path & Physics
Standard OEM factory thermal dissipation rate. Calibrated to stabilize ceramic nose temperature between 500°C–800°C across mixed street, highway, and mountain riding.
Operating Application Envelope
Stock engines, factory ECU mapping, general commuting, and standard touring. Recommended for all baseline maintenance schedules.
Ignitability & Coil Voltage Demand
Standard spark kernel size. Standard secondary coil demand (~15–20 kV). Solid copper core ensures rapid heat conduction away from tip.
SPARK PLUG READING & COMBUSTION DIAGNOSTICS ANALYZER
Interactive visual diagnosis: Match your ceramic insulator tip and electrodes to detect AFR, timing, oil intrusion, and thermal overload
Normal Clean — Optimal Combustion Equilibrium
OPTIMAL COMBUSTIONThermal Operating Range: 500°C – 800°C (932°F – 1,472°F) • Self-Cleaning Pyrolysis Window
Visual Insulator & Electrode Profile
Ceramic insulator nose is light grayish-tan, beige, or light brown. Firing tip and electrodes are dry with minimal combustion deposits. Ground electrode edges remain crisp without rounding or erosion.
Multimeter Electrical Resistance Test
Insulation Resistance > 10 MΩ (Infinite DC resistance between center terminal and steel shell). Dielectric barrier is pristine; zero spark leakage to cylinder head ground.
Probable Root Causes
- Optimal air/fuel ratio across all throttle positions (stoichiometric 14.7:1 cruise, 12.8:1–13.2:1 power enrichment)
- Correct spark plug heat range precisely matched to engine displacement and cooling efficiency
- Ignition timing and coil dwell saturation within factory parameters
- Healthy piston rings and valve guide seals with minimal oil blow-by
Prescribed Workshop Remediation Action
No mechanical intervention required. Inspect gap with wire-style feeler gauge and reinstall to factory torque specification.
Coil-on-Plug (COP) / Stick Coil Multimeter Bench Testing Protocol
Step 1 • Primary Circuit
Set DMM to lowest Ω range. Probe between Terminal 1 (+12V switched) and Terminal 2 (ECU trigger pin). Normal reading: 0.5 - 0.7 Ω (Single Fire Delphi EFI Coil) at 20°C.
Step 2 • Secondary Circuit
Set DMM to kΩ range. Probe between Terminal 1 and the high-voltage spark plug spring terminal inside the boot. Factory spec: 5,500 - 7,500 Ω across secondary towers at 20°C.
Step 3 • Dielectric Boot Inspection
Flex silicone boot under bright light. Check for pinholes, white powdery dielectric breakdown tracks, or hardened silicone causing high-voltage flashover to the cylinder head spark plug tube.
Direct-Fit Ignition Components & Workshop Sockets
Authentic laser iridium plugs, thin-wall magnetic sockets, and OEM replacement stick coils
Harley Davidson Diagnostic Fault Codes & Multimeter Bench Testing
FI & OBD2 DecoderAuthentic factory ECU fault codes, sensor resistance specifications, and harness pinout troubleshooting.
Code P0107Manifold Absolute Pressure (MAP)
MAP sensor input low/open (< 0.20V DC) during key-on or running.
Test: 5.0V VRef at Pin 2; 4.5-5.0V signal key-on engine-off; Pin 1 ground < 0.1V.
Code P0374Crankshaft Position (CKP) Sensor
Zero sync pulses detected from CKP sensor during starter turnover.
Test: Measure 800-1,100 Ω across CKP pins; must generate ≥ 1.0V AC while cranking.
Code P1510Electronic Throttle Control (ETC)
EFI Limited Performance Mode (Limp Mode locked to 20-30% throttle).
Test: Inspect 6-pin throttle body connector for terminal fretting / backprobe TGS 5V sum.
Code B2161Body Control Module (BCM)
Brake Lamp Output open circuit detected when front or rear brake applied.
Test: Test 12V at Blue/Red wire at tail lamp socket; check front brake switch plunger.
Looking for other error codes, sensor pinouts, or OBD2/Euro 5 codes?
OEM Workshop Archives
2 Documented BulletinsOfficial Factory Service Bulletins & Field Updates
Bulletin #M1524M1524: RECALL 0177 - 2019 - 2021 SPORTSTER - HEADLAMP BULB SHIELD
Source: Harley_M1524_Recall0177.pdfMandated Torques:Torque: 5.8–6 in-lbs (0.66–0.68 N·m) (Bulb Shield Screw)Torque: 35–44 in-lbs (4–5 N·m) (Bracket to Visor Screws)Torque: 10–16 ft-lbs (13.5–21.6 N·m) (Visor Bracket Screws)
Consumable Specs:Loctite 243 Medium Strength Blue Threadlocker (HD Part # 99642-97)
Genuine Part Numbers:68297-05A9150010799642-97
Bulletin #Recall0171Part 573 Safety Recall Report 18V-076: ABS Hydraulic Control Unit Flush & Fluid Replacement
Source: Harley_Recall0171_ABS_4574.pdfMandated Torques:Torque: 17–22 ft-lbs (23.0–30.0 N·m) (ABS Manifold / Caliper Banjo Bolts)Torque: 35–61 in-lbs (4.0–6.9 N·m) (Brake Caliper Bleeder Screws)
Consumable Specs:Harley-Davidson Platinum Label DOT 4 Brake Fluid
Genuine Part Numbers:41731-01
Explore Other Subsystems for this 2015 Harley Davidson Twin Cam 96 / 103 (Dyna / Softail / Touring)
Jump straight into dedicated factory specifications and interactive workshop diagnostic engines.
Subsystem Guide/torques
Fastener Torques
Engine drain plug, axle spindles, caliper mounts, triple clamp pinch bolts & thread lubrication derating guide.
Open Dedicated Workbench →
Subsystem Guide/fluids
Fluids & Capacities
Oil: 3.80 L (4.00 US qt) • Coolant: N/A • Brake: DOT 4 Glycol-Based High-Temp (Dry BP ≥ 260°C / Wet BP ≥ 165°C)
Open Dedicated Workbench →
Subsystem Guide/fuses-relays
Fuses & Relays
Main: 50A Maxi-Fuse • Location: N/A
Open Dedicated Workbench →
Subsystem Guide/compression
Compression & Leakdown
Ratio: 9.6:1 • Std: 165-185 PSI • Limit: 140 PSI
Open Dedicated Workbench →
Subsystem Guide/valves
Valve Clearances
Intake: N/A mm • Exhaust: N/A mm
Open Dedicated Workbench →
Subsystem Guide/fuel-delivery
Fuel Delivery & TB Sync
Idle: N/A • Rail Pressure: N/A • Vacuum: N/A
Open Dedicated Workbench →
Subsystem Guide/tires
Tires & Gearing
Front: 130/80B17 (Touring) / 100/90-19 (Dyna) / 130/90B16 (Softail) • Rear: 180/65B16 (Touring) / 160/70B17 (Dyna) / 200/55R17 (Fat Boy)
Open Dedicated Workbench →
Subsystem Guide/suspension
Suspension & Sag
Front Travel: 117 mm • Rear Travel: 76 mm
Open Dedicated Workbench →
Subsystem Guide/maintenance
Maintenance Schedule
Oil: Every 5,000 mi (8,000 km) mi • Valves: N/A • Plugs: Every 10,000 mi (16,000 km) mi
Open Dedicated Workbench →
Looking for direct-fit parts for this 2015 Twin Cam 96 / 103 (Dyna / Softail / Touring)?
Browse authentic verified parts, motor oils, filters, brake pads, and tires that fit this exact bike.