Dedicated Subsystem WorkbenchPlatform Gen: 2018–2026

2026 Ducati Panigale V4 Fuse Box Diagram, Amperages & Relay Diagnostics

Complete fuse box location, blade fuse slot mappings, ISO color codes, blown fuse symptoms and dark current parasitic drain testing for 2026 Ducati Panigale V4.

Gen 2018–2026

Factory Platform Compatibility: All workshop fluid capacities, maintenance milestones, torque specifications, and consumables on this specification sheet are factory-identical across model years 2018 through 2026.

Select Model Year:(Active: 2026)

2018 2019 2020 2021 2022 2023 2024 2025 2026

Engine

1103cc

Drive

525

Cooling

Liquid-Cooled

Factory OEM Fastener Torque Matrix

Multi-System Fastener Torque Quick-Finder & Bolt Grade Matrix

Tightening torques, thread dimensions, socket drive sizes, threadlocker specifications, and sequential tightening procedures for the 2026 Ducati Panigale V4.

Interactive Thread Lubrication & Torque Derating Calculator

Prevent Stripped Threads: Convert Dry Factory Torque Specs to Lubricated Wrench Settings

100% FACTORY DRY SPEC

Torque wrenches measure rotational friction, not axial bolt stretch. Applying dry factory torque specs to threads lubricated with anti-seize, threadlocker, or oil reduces thread friction, causing bolt tension to increase 30%–50% at the same wrench setting and stripping soft aluminum motorcycle castings. Select your active fastener thread condition below:

Dry Threads (Factory Baseline): Clean, dry threads with zero lubricant. 100% of factory torque spec.

Engine & DrivetrainNone (Clean Dry)

Engine Oil Drain Bolt

Tightening Torque

42 N·m

31 ft-lb

Thread Dimension

M22 × 1.5

Socket / Drive

10 mm Allen

Sequence: Hand-spin until washer seats flush against sump; torque in single continuous stroke.

CRITICAL CAUTION: Over-torquing strips soft aluminum oil pans requiring permanent Heli-Coil or Time-Sert insert repair.

Engine & DrivetrainEngine Oil (Pre-Lube)

Engine Oil Filter (Spin-on / Cover)

Tightening Torque

11 N·m

97 in-lb

Thread Dimension

M20 × 1.5

Socket / Drive

65 mm / 68 mm Filter Cup

Sequence: Lubricate rubber O-ring with fresh clean engine oil before spinning on. Tighten until gasket contacts, then advance 2 to 2.5 full turns.

CRITICAL CAUTION: Never install dry rubber seal. Dry gaskets pinch, buckle, and spray oil onto the rear tire at highway speed.

Engine & DrivetrainNone (Clean Dry Plated Threads)

Spark Plugs (Cold Engine)

Tightening Torque

12 N·m

106 in-lb

Thread Dimension

M10 × 1.0

Socket / Drive

16 mm (5/8 in) Thin-Wall Magnetic Socket

Sequence: Hand-thread all plugs using rubber hose extension until seated. Torque strictly on cold engine (≤ 35°C / 95°F).

CRITICAL CAUTION: Modern NGK/Denso trivalent plated threads require zero anti-seize. Torquing hot heads strips aluminum spark plug threads.

Engine & DrivetrainNone (Clean Dry)

Clutch Pressure Plate Spring Bolts

Tightening Torque

10 N·m

89 in-lb

Thread Dimension

M6 × 1.0

Socket / Drive

10 mm Socket / 8 mm Hex

Sequence: Criss-cross diagonal pattern across 3 stages (finger tight → 5 N·m → 10 N·m) to seat pressure plate completely flat.

CRITICAL CAUTION: Uneven tightening tilts the clutch pressure plate, snapping delicate aluminum clutch basket lifter posts.

Engine & DrivetrainNone (Clean Dry)

Clutch Outer Case Cover Bolts

Tightening Torque

10 N·m

89 in-lb

Thread Dimension

M6 × 1.0

Socket / Drive

8 mm Hex Socket

Sequence: Criss-cross pattern starting from center bolts moving outward. Verify dowel alignment pins seat fully.

CRITICAL CAUTION: M6 bolts into aluminum engine cases snap easily. Always use a precision low-range 1/4" drive torque wrench.

Engine & DrivetrainMedium Strength (Blue 242/243) on Stator Wire Bracket

Alternator / Stator Cover Bolts

Tightening Torque

10 N·m

89 in-lb

Thread Dimension

M6 × 1.0

Socket / Drive

8 mm Hex Socket

Sequence: Criss-cross pattern. Apply thin bead of ThreeBond / RTV sealant only at rubber grommet wire passthrough.

CRITICAL CAUTION: Powerful magnetic rotor will violently snap the cover against the engine case during installation; keep fingers clear.

Engine & DrivetrainMedium Strength (Blue 242/243) + Bend Lock Washer

Countershaft Front Sprocket Nut

Tightening Torque

85 N·m

62.7 ft-lb

Thread Dimension

M20 × 1.5

Socket / Drive

32 mm Socket

Sequence: Have assistant hold rear foot brake firmly. Torque nut to spec, then fold lock washer ear flat against hex flat.

CRITICAL CAUTION: A loose countershaft nut will machine through the engine crankcase or lock the transmission at highway speed.

Engine & DrivetrainMedium Strength (Blue 242/243) / OEM Metal Locknuts

Rear Drive Sprocket Stud Nuts

Tightening Torque

80 N·m

59 ft-lb

Thread Dimension

M10 × 1.25 Self-Locking

Socket / Drive

14 mm / 17 mm Socket

Sequence: Criss-cross star pattern in 2 stages to ensure rear sprocket sits 100% flush against the cush drive hub flange.

CRITICAL CAUTION: Loose rear sprocket nuts will cock sideways, gouging the aluminum swingarm and throwing the drive chain.

Chassis & SuspensionNone (Clean Dry Threads / Light Grease on Shaft)

Front Wheel Axle Spindle / Bolt

Tightening Torque

63 N·m

46.5 ft-lb

Thread Dimension

M25 × 1.25

Socket / Drive

30 mm Socket

Sequence: Torque axle bolt first while pinch bolts remain loose. Pump front forks 3–4 times before torquing pinch bolts.

CRITICAL CAUTION: Torquing pinch bolts before axle nut causes fork binding, stiction, and severe front brake shudder.

Chassis & SuspensionNone (Clean Dry)

Front Axle Fork Bottom Pinch Bolts

Tightening Torque

19 N·m

14 ft-lb

Thread Dimension

M8 × 1.25

Socket / Drive

6 mm Allen / 12 mm Socket

Sequence: Dual pinch forks: alternate tightening between inner and outer bolt 3 times until wrench clicks on both without moving.

CRITICAL CAUTION: Tightening one bolt relaxes the adjacent bolt. Failure to alternate causes pinch bolts to work loose under road vibration.

Chassis & SuspensionNone (Factory Locknut / Cotter Pin)

Rear Axle Castle / Flange Nut

Tightening Torque

230 N·m

169.6 ft-lb

Thread Dimension

M48 × 1.5 Single-Sided

Socket / Drive

55 mm 12-Point Socket

Sequence: Push wheel forward against adjusters while torquing. Insert fresh cotter pin or R-clip through castle slot.

CRITICAL CAUTION: Under-torquing allows axle cocking, throwing wheel out of alignment; over-torquing crushes wheel bearing spacer tubes.

Chassis & SuspensionMedium Strength (Blue 242/243)

Rear Shock Upper & Lower Mount Bolts

Tightening Torque

44 N·m

32.5 ft-lb

Thread Dimension

M10 × 1.25

Socket / Drive

14 mm / 17 mm Socket

Sequence: Torque bolts with rear suspension loaded at static ride height (wheel on ground), not at full hanging droop.

CRITICAL CAUTION: Torquing shock eyelet rubber/spherical bushings at full droop locks preload twist into bushings, causing premature bushing tear.

Chassis & SuspensionNone (Clean Dry)

Swingarm Pivot Shaft Nut

Tightening Torque

100 N·m

73.8 ft-lb

Thread Dimension

M18 × 1.5

Socket / Drive

22 mm / 27 mm Socket

Sequence: Set swingarm pivot thrust collar clearance with spanner tool before torquing central through-shaft nut.

CRITICAL CAUTION: Incorrect pivot preload crushes needle bearings or induces lateral swingarm wobble and high-speed tank-slappers.

Cockpit & SteeringNone (Clean Dry)

Upper Triple Clamp (Fork Bridge) Pinch Bolts

Tightening Torque

24 N·m

17.7 ft-lb

Thread Dimension

M8 × 1.25

Socket / Drive

6 mm Allen / 12 mm Socket

Sequence: Verify fork tube height / stanchion protrusion above top bridge matches factory spec with vernier caliper before tightening.

CRITICAL CAUTION: Uneven fork tube heights alter chassis steering geometry, trail, and induce high-speed head-shake.

Cockpit & SteeringNone (Clean Dry)

Lower Triple Clamp Pinch Bolts

Tightening Torque

18 N·m

13.3 ft-lb

Thread Dimension

M8 × 1.25

Socket / Drive

6 mm Allen / 12 mm Socket

Sequence: Alternate between upper and lower bolt on each side 3 times to achieve uniform clamping without localized tube deformation.

CRITICAL CAUTION: CRITICAL: Overtightening lower clamp pinches the outer fork slider oval, locking fork bushings and causing severe suspension stiction.

Cockpit & SteeringNone (Clean Dry)

Handlebar Riser Clamps / Clip-on Clamps

Tightening Torque

24 N·m

17.7 ft-lb

Thread Dimension

M8 × 1.25

Socket / Drive

6 mm Allen Socket

Sequence: MANDATORY ZERO-GAP RULE: Tighten front bolts until clamp casting touches bottom casting with zero gap; then torque rear bolts to spec.

CRITICAL CAUTION: Leaving a gap at the front bolts allows handlebars to slip under sudden hard emergency braking.

Cockpit & SteeringNone (Clean Dry)

Steering Stem Head Nut

Tightening Torque

110 N·m

81.1 ft-lb

Thread Dimension

M28 × 1.0

Socket / Drive

30 mm / 36 mm Socket

Sequence: Ensure upper triple clamp pinch bolts are loose when torquing stem nut to prevent binding the steering bearings.

CRITICAL CAUTION: This nut clamps the top bridge; steering head bearing preload is adjusted separately via the lower castle spanner ring.

Cockpit & SteeringNone (Clean Dry)

Front Brake Master Cylinder Clamp Bolts

Tightening Torque

10 N·m

89 in-lb

Thread Dimension

M6 × 1.0

Socket / Drive

8 mm Hex / 5 mm Allen

Sequence: Align "UP" arrow mark on split clamp upward. Tighten upper bolt first until clamp seats flush; then torque lower bolt to 10 N·m.

CRITICAL CAUTION: Tightening bottom bolt first pinches the reservoir casting unevenly, cracking master cylinder clamp ears.

Brakes & HydraulicsMedium Strength (Blue 242/243) / Factory Micro-Encapsulated

Front Brake Caliper Mount Bolts

Tightening Torque

45 N·m

33.2 ft-lb

Thread Dimension

Radial M10 × 1.25

Socket / Drive

12 mm / 14 mm Socket (T50 Torx on BMW)

Sequence: Radial calipers: tighten upper and lower bolts in two equal stages (20 N·m, then final spec).

CRITICAL CAUTION: Radial caliper mounting threads tap directly into aluminum fork bottoms. Never use pneumatic/electric impact guns.

Brakes & HydraulicsMedium Strength (Blue 242/243)

Rear Brake Caliper Mount / Bracket Bolts

Tightening Torque

23 N·m

17 ft-lb

Thread Dimension

M8 × 1.25

Socket / Drive

12 mm Socket / 6 mm Allen

Sequence: Ensure caliper bracket sliding torque arm slot engages swingarm tab cleanly before tightening.

CRITICAL CAUTION: Unengaged bracket tabs allow rear caliper to rotate with disc during braking, shearing brake lines.

Brakes & HydraulicsMedium Strength (Blue 242/243 Mandatory)

Front Brake Disc Rotor Bolts

Tightening Torque

25 N·m

18.4 ft-lb

Thread Dimension

M8 × 1.25 Low-Profile Shoulder

Socket / Drive

6 mm Allen / T40 Torx

Sequence: Clean wheel hub female threads with solvent; apply 2 drops of Blue 243. Tighten in criss-cross star pattern across 2 stages.

CRITICAL CAUTION: A loose brake rotor bolt can back out and impact the front fork leg, instantly locking the front wheel.

Brakes & HydraulicsMedium Strength (Blue 242/243 Mandatory)

Rear Brake Disc Rotor Bolts

Tightening Torque

25 N·m

18.4 ft-lb

Thread Dimension

M8 × 1.25 / M10 × 1.25

Socket / Drive

6 mm Allen / T40 Torx

Sequence: Criss-cross star pattern. Ensure disc sits 100% flat against wheel hub register with zero trapped debris.

CRITICAL CAUTION: Trapped dirt under rotor mounting flange causes severe brake pedal pulsation and lateral rotor runout.

Brakes & HydraulicsNone (Clean Dry with Fresh Copper Washers)

Hydraulic Brake Line Banjo Bolts

Tightening Torque

30 N·m

22.1 ft-lb

Thread Dimension

M10 × 1.25 (Brembo: M10 × 1.0)

Socket / Drive

12 mm / 14 mm Hex Socket

Sequence: Always replace the two copper/aluminum crush washers per banjo joint. Never reuse crushed washers.

CRITICAL CAUTION: Over-torquing shears the cross-drilled fluid passage inside the banjo bolt, destroying the caliper casting.

Brakes & HydraulicsNone (Clean Dry)

Caliper Hydraulic Bleed Screws

Tightening Torque

6 N·m

53 in-lb

Thread Dimension

M7 × 1.0 / M8 × 1.25

Socket / Drive

8 mm / 10 mm Line Wrench

Sequence: Use 6-point flare-nut / line wrench to prevent rounding soft hex. Snug firmly until seated against conical seat.

CRITICAL CAUTION: Overtightening distorts the internal conical sealing point, causing persistent hydraulic fluid weeping.

Four Essential Workshop Tightening Protocols

1. Lower Triple Clamp Stiction Rule

Lower triple clamp pinch bolts must NEVER be torqued past factory spec (18–23 N·m). Overtightening pinches the outer fork slider oval, crushing internal bushings against the chrome stanchion and causing severe suspension stiction and premature seal failure.

2. Handlebar Clamp Zero-Gap Rule

Always tighten the front two clamp bolts until the upper clamp touches the bottom riser with ZERO clearance. Then torque the rear two bolts to spec. Leaving an equal gap front and rear allows handlebars to slip forward under sudden emergency braking.

3. Front Axle Bounce & Alignment

Torque front axle spindle nut first while pinch bolts are loose. Pump front forks up and down vigorously 3–4 times with front brake applied. This allows the right fork bottom to center itself freely along the axle spindle before torquing pinch bolts.

4. Star Pattern & Criss-Cross Torque

Always torque opposed bolts across a circular pattern in 2 progressive stages (50% torque stage 1, 100% final stage). Essential on brake disc rotors, engine case covers, and clutch pressure plates to prevent warping aluminum mating faces.

Metric Bolt Strength Grade & Tensile Markings Guide

Grade 8.8

Standard High Tensile (800 MPa)

Yield strength: 640 MPa. Used on footpeg brackets, fairing subframes, radiator brackets, and standard chassis mounts. Head stamped "8.8".

Grade 10.9

Extra High Tensile (1,040 MPa)

Yield strength: 940 MPa. Mandatory on front/rear brake caliper mounts, suspension linkages, and engine hanger bolts. Head stamped "10.9".

Grade 12.9

Ultra High Tensile (1,220 MPa)

Yield strength: 1,100 MPa. Extreme strength alloy steel used on cylinder head studs, crankcase through-bolts, and countershaft sprocket studs. Head stamped "12.9".

Stainless A2-70 / A4-80

Galling Hazard in Aluminum

Stainless steel galls into aluminum engine cases, seizing permanently. Never replace structural chassis or brake bolts with cosmetic hardware store stainless.

Browse Calibrated Torque Wrenches (1/4", 3/8", 1/2")→Shop Threadlockers & Primer Cleaners→Shop Metric Hex & Torx Sockets→

CIRCUIT HEALTH DECKMain: 30A Blade / Starter SolenoidSpec: < 2 mA Quiescent

FUSE BOX, RELAY ASSIGNMENTS & PARASITIC DRAIN ISOLATOR

Fuse & Relay Location: Main fuse box located under rider seat forward of battery; Main 30A fuse mounted directly to starter solenoid next to battery tray.

Select Fuse to Inspect Circuits & Failure SymptomsFormat: Mini Blade (ATM)

5A

SLOT: KEY SENSE

Key-On Logic & BBS

Rating: 5 Amps

Downstream Protected Components:

Black Box System (BBS)Immobilizer AntennaHands-Free Lock

Mechanic Diagnostic: Symptoms If Blown

Dash will not wake up; Hands-Free key not recognized.

Shop Replacement 5A Fuses

Official NHTSA Safety Recalls & Technical Bulletins

1 Active Campaign

U.S. Department of Transportation compliance database (Title 49 U.S.C. Chapter 301).

Verify VIN on NHTSA.gov

The U.S. National Highway Traffic Safety Administration reports 1 safety recall campaign associated with this platform. Independent repair shops and riders should confirm that authorized dealership warranty remedies have been applied.

NHTSA #26V050000SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS

Received: 28/01/2026▼

Defect Description

Ducati North America (Ducati) is recalling certain 2025-2026 Streetfighter V4, Streetfighter V4 S, Panigale V4, and Panigale V4 S motorcycles. Excessive heat may damage the rear brake hose between the ABS control unit and brake caliper, resulting in a sudden loss of the rear brakes.

Safety Hazard / Consequence

A sudden loss of rear brake function increases the risk of a crash or injury.

Factory Remedy & Repair Action

Dealers will replace the thermal shield, free of charge. Owner notification letters were mailed March 9, 2026. Owners may contact Ducati customer service at 1-888-391-5446. Ducati's number for this recall is SRV-RCL-26-001. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 3, 2026. This recall expands and replaces previous NHTSA recall number 25V013. Vehicles repaired under the previous recall will need to have the new remedy completed.