Dedicated Subsystem WorkbenchPlatform Gen: 2018–2026
2019 Ducati Panigale V4 / V4 S / V4 R / V4 SP Factory Maintenance Schedule & Service Punch-List
Official manufacturer service intervals (4k, 8k, 12k, 16k, 24k miles), interactive workshop maintenance punch-list, and DIY vs dealership cost estimator for 2019 Ducati Panigale V4 / V4 S / V4 R / V4 SP.
Gen 2018–2026
Factory Platform Compatibility: All workshop fluid capacities, maintenance milestones, torque specifications, and consumables on this specification sheet are factory-identical across model years 2018 through 2026.
OEM Workshop Archives
5 Documented BulletinsOfficial Factory Service Bulletins & Field Updates
Bulletin #SRV-RCL-25-002Safety Recall 25V-570: Panigale V4 & Streetfighter V4 Single-Sided Swingarm Rear Wheel Axle Shaft Replacement
Source: RCLRPT-25V570-3457.pdfMandated Torques:Rear Wheel Collar Nut (M48x1.5): 230 N·m ± 5% (55mm 12-point socket, Shell Retinax HD2 grease)Eccentric Hub Pinch Clamp Screws (2x M12): 35 N·m ± 5% (1-2-1 alternating sequence)Rear Sprocket Cush Drive Nuts (6x M10x1.25): 48 N·m ± 5% (Loctite 243)Rear Brake Rotor Screws (4x M8x20): 25 N·m ± 5% (Loctite 270)
Consumable Specs:Shell Retinax HD2 or Gadus high-load axle greaseLoctite 243 medium-strength threadlockerLoctite 270 high-strength threadlocker
Genuine Part Numbers:81920831AA (Recalled Rear Wheel Shaft)81920611A (Recalled Rear Axle Assembly)81920951AA (Countermeasure Rear Wheel Shaft)75010071E (M48x1.5 Wheel Collar Nut)85210571A (Conical Belleville Spring Washer)75990081A (Safety Circlip Hairpin Pin)
NHTSA Recall 25V-570Ducati Campaign SRV-RCL-25-002
Ducati Panigale V4 / Streetfighter V4 Single-Sided Swingarm Rear Wheel Axle Shaft
Structural integrity recall: Replacement of rear wheel shaft (81920831AA / 81920611A), notch effect mitigation, M48 collar nut 230 N·m & eccentric clamp 35 N·m.
Critical Safety CampaignM48 Nut 230 N·m / Eccentric 35 N·m
Genuine Part Numbers:81920831AA81920611A81920951AA75010071E
NHTSA Safety Campaign 25V-570 / Ducati SRV-RCL-25-002Desmosedici Stradale / Single-Sided Swingarm Platform
Bulletin #SRV-RCL-18-006Safety Recall 18V-834 / CR167: Panigale V4 Oil Cooler Output Port Welded Reinforcement & Hose Fittings
Source: RCRIT-18V834-1259.pdfMandated Torques:Oil Cooler Delivery & Return Hose Nuts: 15 N·m ± 10% (24mm open crowfoot socket adapter)Oil Cooler Radiator Duct Stud Nuts (2x M6): 5 N·m ± 10%Lower Half-Fairing Screws (M5x14): 4 N·m ± 10%
Consumable Specs:Shell Advance 4T Ultra 15W-50 (0.42 L top-up quantity)Klüberplus S 06/100 rubber vibration isolator assembly lubricantClean engine oil for Viton O-rings
Genuine Part Numbers:54811364A (Countermeasure Oil Cooler with Welded Gusset Plates)88641321A (Viton Fluoroelastomer O-Ring Seals, 4x)71314901A (Vibration Damper Spacers with Collar, 2x)
NHTSA Recall 18V-834Ducati Campaign SRV-RCL-18-006 / CR167
Ducati Panigale V4 Oil Cooler Output Port Reinforcement & Hose Fittings
Countermeasure cooler (54811364A) with dual welded port reinforcement plates, 24mm union nuts 15 N·m, duct mounts 5 N·m & 0.42L top-up.
Thermal Reliability UpdateHose Unions 15 N·m / Mounts 5 N·m
Recall Countermeasure Kit:54811364A88641321A71314901A
NHTSA Safety Campaign 18V-834 / Ducati SRV-RCL-18-006 / CR167Panigale V4 / V4 S / V4 Speciale (2018–2019)
Bulletin #SRV-RCL-18-008Safety Recall 18V-854 / CR169: Desmosedici Stradale Hydraulic Timing Chain Tensioner Torque Revision
Source: RCRIT-18V854-6810.pdfMandated Torques:Front Bank Hydraulic Chain Tensioner: 50 N·m ± 5% (27mm 12-point box socket, revised from 30 Nm)Rear Bank Hydraulic Chain Tensioner: 50 N·m ± 5% (27mm 12-point box socket, revised from 30 Nm)Left Fairing Puller Screws (M5x12): 5 N·m ± 10%
Consumable Specs:None (dry threads; interference crush washer A seated on tensioner body)
Genuine Part Numbers:42610491A (Hydraulic Chain Tensioner Assembly with Washer A)Washer A (Interference-fit seal ring; replace complete tensioner if missing)
NHTSA Recall 18V-854Ducati Campaign SRV-RCL-18-008 / CR169
Ducati Desmosedici Stradale Hydraulic Timing Chain Tensioner Sealing
Front and rear bank hydraulic chain tensioner torque revision: 50 N·m (increased from 30 N·m), 27mm 12-point socket & washer inspection.
Torque Revision Campaign50 N·m (27mm Box Socket)
NHTSA Safety Campaign 18V-854 / Ducati SRV-RCL-18-008 / CR169Desmosedici Stradale V4 1103cc / 998cc Platform
Bulletin #SRV-RCL-19-001Safety Recall 19V-382 & 18V-238 / CR177: Panigale V4 Fuel Tank Filler Cap Venting System & Check Ball Deletion
Source: RCSB-19V382-9239.pdfMandated Torques:Valve Block Fastening Screws (2x Torx T10): 0.9 N·mFiller Plug Outer Ring Screws (4x M5x16): 4 N·m ± 10%Fuel Tank Front Pivot Screw (M6x20): 10 N·m ± 10%
Consumable Specs:None
Genuine Part Numbers:43314761A (Fuel Tank Warning Decal: Fuel spray may cause injury, Open slowly)43314751A (Owner's Manual Rider Handbook Addendum Page)Check Ball 7 (Permanently extracted and deleted from valve chamber)
NHTSA Recall 19V-382 & 18V-238Ducati Campaign SRV-RCL-19-001 / CR177
Ducati Panigale V4 Fuel Tank Filler Cap Venting & Pressure Relief System
Fuel pressurization countermeasure: Valve block check ball removal, Torx T10 0.9 N·m, M5 ring screws 4 N·m & decal 43314761A.
Fuel Safety RecallCap Screws 4 N·m / Valve 0.9 N·m
Campaign Components:43314761A43314751ACheck Ball RemovalDDS 2.0 Global Scan
NHTSA Safety Campaign 19V-382 / 18V-238 / Ducati SRV-RCL-19-001Panigale V4 (all variants 2018–2019)
Bulletin #SRV-RCL-26-001Safety Recall 26V-050: Panigale V4 & Streetfighter V4 Rear Brake Line Heat Shield Protection
Source: RCLRPT-26V050.pdfMandated Torques:Rear Brake Line Banjo Screws: 25 N·m ± 5%Heat Shield Retaining Bracket Screws: 5 N·m ± 10%
Consumable Specs:DOT 4 Brake FluidThermal Shield Reflective Sleeve
Genuine Part Numbers:High-temperature thermal reflective sleeve assemblyCopper crush sealing washers
Factory Service Schedule
Scheduled Maintenance Punch-List & Service Estimator
Select a factory interval milestone or enter your current odometer reading to preview scheduled workshop tasks for the 2019 Ducati Panigale V4 / V4 S / V4 R / V4 SP.
ODOMETER:MILES
FACTORY INTERVALS:
Workshop Tablet Punch-List Progress0 of 9 Tasks Signed Off (0%)
Fluids & Engine
INSPECT / OK~0.8 HR EST
Engine Oil & Filter Element Replacement
3.80 L (4.02 US qt) / Shell
- Drain Plug Torque: Not Available - Refer to Factory Workshop Manual
- Always install a fresh OEM aluminum crush washer (M12/M14)
- Pre-lube new filter O-ring with fresh engine oil prior to spin-on install
- Warm engine to operating temperature before draining for complete sediment evacuation
TOOLS: 17mm Hex Socket + 65mm 14-Flute Filter Cup
PARTS/FLUIDS: Shell Full Synthetic 4T Oil + Filter + Crush Washer
Ignition & Air
INSPECT / OK~1.2 HR EST
Spark Plug Inspection / Direct-Replacement
NGK RMAR9A-10 (Gap: 0.9 - 1.0 mm)
- Tightening Torque: Not Available - Refer to Factory Workshop Manual
- Hand-thread plug completely down to cylinder head seat before applying torque wrench
- Inspect electrode coloration for stoichiometric AFR balance (tan/light grey)
- Apply thin film of dielectric grease to interior of coil-on-plug boots
TOOLS: 14mm / 16mm Thin-Wall Spark Plug Socket + Feeler Gauge
PARTS/FLUIDS: NGK RMAR9A-10 + Dielectric Silicone Grease
Hydraulics & Brakes
INSPECT / OK~1 HR EST
Brake Fluid Full Hydraulic Flush & De-Aeration
DOT 4 (Brembo HTC 64T / Motul RBF 660 for track) Flush (Front Dual + Rear)
- Bleeder Nipple Torque: 7 N·m (Do not over-torque aluminum threads)
- Hygroscopic degradation: brake fluid absorbs atmospheric moisture; discard if moisture > 3.7%
- Flush master cylinder reservoir completely before cycling ABS hydraulic modulator
- Wash painted/plastic bodywork immediately with clean water if fluid contact occurs
TOOLS: 8mm / 10mm Bleeder Box Wrench + Clear Bleeder Hose + Catch Bottle
PARTS/FLUIDS: DOT 4 (Brembo HTC 64T / Motul RBF 660 for track) + Isopropyl Alcohol
Hydraulics & Brakes
DUE NOW~0.4 HR EST
Rotor Thickness & Pad Friction Lining Inspection
Front Min: 4.5 mm | Rear Min: 4.5 mm
- Front Caliper Mounting Torque: 45 N·m
- Minimum friction material thickness: 1.0 mm (excluding steel backing plate)
- Check rotor surface for deep grooving, heat bluing, or radial thermal stress cracks
- Verify caliper slide pins are free of corrosion and lubricated with silicone grease
TOOLS: Digital Micrometer (0-25mm) + Vernier Caliper + Torx T50 / 12mm Socket
PARTS/FLUIDS: Brake Contact Degreaser + High-Temp Synthetic Caliper Pin Grease
Drivetrain
DUE NOW~0.4 HR EST
Drive Chain Slack Inspection, Adjustment & Lube
Chain Slack: 20 - 30 mm (on side stand)
- Clean chain with O-ring safe chain degreaser; do not use harsh solvents or wire brushes
- Measure chain slack at midpoint of lower run; adjust to 20-30 mm tolerance
- Torque rear axle spindle nut: Not Available - Refer to Factory Workshop Manual
- Apply synthetic high-adhesion chain wax/lube to interior run of rollers
TOOLS: Rear Axle Socket (27mm/32mm) + Alignment Gauge + Torque Wrench
PARTS/FLUIDS: O-Ring Safe Chain Degreaser + Synthetic Chain Lube
Ignition & Air
INSPECT / OK~0.5 HR EST
Engine Air Intake Filter Element Service
OEM High-Efficiency Paper Element / Multi-Layer Cotton
- Remove fuel tank / side fairing panels to access airbox cover screws
- Inspect airbox lower cavity and drain hose for blowby oil condensation
- Do not blow compressed air through viscous paper filter elements (destroys filtration matrix)
- Verify airbox lid seal is properly seated to prevent unfiltered dust bypass
TOOLS: 4mm / 5mm Hex Allen Wrenches + JIS #2 Screwdriver
PARTS/FLUIDS: Replacement OEM Air Filter Element + Clean Microfiber Cloth
Fluids & Engine
INSPECT / OK~1 HR EST
Engine Cooling System Flush & Radiator De-Aeration
Silicate & Borate-Free HOAT 50:50 Premix (-37°C / -35°F)
- Only open radiator cap when engine is completely cold (ambient temperature)
- Drain coolant from water pump drain bolt and radiator lower hose connection
- Flush cooling circuit with distilled water before filling with fresh 50:50 HOAT coolant
- Cycle engine until radiator fan activates, then burp cooling jacket to eliminate air pockets
TOOLS: 8mm / 10mm Drain Bolt Socket + Catch Pan + Radiator Cap Tester
PARTS/FLUIDS: Silicate-Free Long-Life Motorcycle Coolant (50:50 Distilled Water Premix)
Valvetrain
INSPECT / OK~3.8 HR EST
Valve Clearance Inspection & Camshaft Timing Audit
Not Available
- Strict requirement: engine must be cold (temperature <= 35°C / 95°F) for accurate readings
- Rotate crankshaft to compression Top Dead Center (TDC) for each cylinder firing order
- Shim Diameter: Not Available
- Replace valve cover gasket and spark plug well O-rings upon reassembly
TOOLS: Angled Blade Feeler Gauges (0.04-0.35mm) + Digital Micrometer + Magnet Pen
PARTS/FLUIDS: Valve Shim Assortment Kit + OEM Valve Cover Gasket + ThreeBond Liquid Gasket
Chassis & Safety
DUE NOW~0.5 HR EST
Chassis, Axle & Safety Critical Fastener Audit
Front Axle: Not Available - Refer to Factory Workshop Manual | Rear Axle: Not Available - Refer to Factory Workshop Manual
- Front Axle Pinch Bolts: Factory Torque Spec
- Front Caliper Mounting Bolts: 45 N·m
- Check triple clamp pinch bolts, handlebar clamps, and footpeg brackets
- Inspect steering head bearings for notchiness or play at center-detent
TOOLS: Calibrated 3/8" & 1/2" Click-Type Torque Wrenches + Metric Sockets
PARTS/FLUIDS: Blue Medium-Strength Threadlocker (Loctite 243)
Tool Pre-Flight
Calibrated Instruments & Drive SpecificationsWorkshop Tool & Chemical Pre-Flight Card
Sockets, Hex Bits & Wrenches
17mm Metric Hex Socket
Engine oil drain plug removal & torquing
65mm 14-Flute Oil Filter Cup Wrench
Spin-on oil filter removal & install (3/8" drive)
14mm / 16mm Thin-Wall Spark Plug Socket
Spark plug removal & installation
12mm / 14mm Radial Caliper Socket
Brake caliper mounting bolts
8mm / 10mm Bleeder Box Wrench
Hydraulic caliper bleed nipple opening
Front & Rear Axle Sockets (19mm - 32mm)
Wheel axle spindle nuts & chain adjustment
Calibrated Precision Instruments
1/4" Drive Torque Wrench (5 - 25 N·m)
Bleed valves, spark plugs, casing screws
1/2" Drive Torque Wrench (30 - 160 N·m)
Axle nuts, caliper bolts, drain plugs
Angled Blade Feeler Gauge Set (0.04 - 0.35 mm)
Valve clearances & spark plug electrode gap
Digital Rotor Micrometer (0 - 25 mm)
Brake disc minimum discard thickness verification
Workshop Chemicals & Consumables
Blue Medium Threadlocker (Loctite 243)
Brake caliper, rotor, and footpeg fasteners
High-Temp Anti-Seize Paste
Spark plug threads & axle spindle coating
DOT 4 Synthetic Brake Fluid
Hydraulic brake & clutch system flushing
Synthetic O-Ring Chain Degreaser & Lube
Drive chain cleaning & roller lubrication
New OEM Aluminum Crush Washers (M12 / M14)
Oil drain plug sealing (single-use)
Dealership Flat-Rate Labor vs. DIY Workshop Cost Estimator
Compare authorized dealership retail service invoicing against performing scheduled maintenance in your private shop.
DEALER LABOR RATE:$150/hr
Estimated Dealership Retail Invoice
Flat-Rate Labor (1.3 hrs @ $150/hr):$195.00
OEM Fluids & Parts (35% Dealer Markup):$61.00
Shop Supplies & Waste Disposal Fee:$25.00
Dealership Quote Subtotal:$281.00
DIY Private Workshop Investment
Factory Fluids & Replacement Filters:$45.00
Workshop Mechanical Labor:$0.00 (Owner Performed)
Environmental Disposal Fee:$0.00 (Free Auto Recycling)
Total DIY Investment:$45.00
You Save $236.00 (84%) by Servicing in Your Workshop
Includes matched OEM fluid capacities, filter, and authentic factory torque specifications.
1-Click Factory Service KitOEM Spec Fluid Capacities Matched
Workshop Maintenance Kit & Factory Fluids
Authentic factory-grade motor oil, oil filter, and high-temp brake fluid matched precisely to 2019 Ducati Panigale V4 / V4 S / V4 R / V4 SP capacities.
Full Kit Subtotal
$74.50
Matches factory 15W-50 spec (Oil spec: 3.80 L (4.02 US qt))
Item Price
$68.95
DOT 4 Synthetic Formula
EBC High-Performance DOT 4 Synthetic Brake Fluid
8.8 oz (250 ml) Workshop Bottle
Meets & exceeds factory DOT 4 (Brembo HTC 64T / Motul RBF 660 for track) specifications
Item Price
$5.55
Factory OEM Spark Plug Spec
NGK RMAR9A-10
Gap: 0.9 - 1.0 mm (0.035 - 0.039 in)
Inspection milestone: 15,000 miles (24,000 km) miles. Exact factory part specification.
Authentic OEM Reference
Search OEM Plugs →Explore Other Subsystems for this 2019 Ducati Panigale V4 / V4 S / V4 R / V4 SP
Jump straight into dedicated factory specifications and interactive workshop diagnostic engines.
Subsystem Guide/torques
Fastener Torques
Engine drain plug, axle spindles, caliper mounts, triple clamp pinch bolts & thread lubrication derating guide.
Open Dedicated Workbench →
Subsystem Guide/fluids
Fluids & Capacities
Oil: 3.80 L (4.02 US qt) • Coolant: 2.60 L (2.75 US qt) • Brake: DOT 4 (Brembo HTC 64T / Motul RBF 660 for track)
Open Dedicated Workbench →
Subsystem Guide/fuses-relays
Fuses & Relays
Main: N/A • Location: N/A
Open Dedicated Workbench →
Subsystem Guide/compression
Compression & Leakdown
Ratio: 14.0:1 • Std: 185-235 PSI • Limit: 160 PSI
Open Dedicated Workbench →
Subsystem Guide/valves
Valve Clearances
Intake: N/A mm • Exhaust: N/A mm
Open Dedicated Workbench →
Subsystem Guide/fuel-delivery
Fuel Delivery & TB Sync
Idle: N/A • Rail Pressure: N/A • Vacuum: N/A
Open Dedicated Workbench →
Subsystem Guide/electrical
Charging & Battery
Battery: YT12B-BS (12V 10Ah) / Lithium-Ion (12V 4Ah, OEM 66920031A on V4 S / SP / R)
Open Dedicated Workbench →
Subsystem Guide/tires
Tires & Gearing
Front: 120/70 ZR17 (Pirelli Diablo Supercorsa SP V3 / V4) • Rear: 200/60 ZR17 (Pirelli Diablo Supercorsa SP V3 / V4)
Open Dedicated Workbench →
Subsystem Guide/suspension
Suspension & Sag
Front Travel: 120 mm • Rear Travel: 130 mm
Open Dedicated Workbench →
Looking for direct-fit parts for this 2019 Panigale V4 / V4 S / V4 R / V4 SP?
Browse authentic verified parts, motor oils, filters, brake pads, and tires that fit this exact bike.