Dedicated Subsystem WorkbenchPlatform Gen: 2013–2018

2016 BMW R 1200 GS Tire Sizes, Cold Pressures & Gearing Ratios

OEM tire sizes, front cold PSI (), rear cold PSI (), sprocket teeth count, final drive ratio, and chain pitch for 2016 BMW R 1200 GS.

Gen 2013–2018

Factory Platform Compatibility: All workshop fluid capacities, maintenance milestones, torque specifications, and consumables on this specification sheet are factory-identical across model years 2013 through 2018.

Select Model Year:(Active: 2016)

2013 2014 2015 2016 2017 2018

Engine

1170cc

Drive

Chain

Cooling

Liquid/Air-Cooled

Tire Engineering & Multi-Scenario Pressure Matrix

ETRTO Validated

Inflation targets calibrated across operating modes, verified rim width ranges, and certified alternate sizes.

Shop Direct-Fit Tires

Multi-Scenario Inflation Pressures

Solo Street / CommutingCold Baseline

Front: 36 PSI

Rear: 42 PSI

Two-Up Passenger & LuggageMax Load

Front: 38 PSI

Rear: 42 PSI

Off-Highway / Terrain Pressure

Maintain OEM cold baseline for street transfers; adjust -2 to -4 PSI for loose terrain.

Rim Geometry & ETRTO Envelopes

Front Wheel

OEM Rim Width:3.00"

Permissible Envelope:3.00" - 3.50"

Rear Wheel

OEM Rim Width:4.50"

Permissible Envelope:4.50" - 5.00"

Operating outside ETRTO envelope width alters crown radius, accelerates shoulder wear, and impacts lean stability.

Factory Dimensions & Verified Alternates

Factory Standard Sizes

Front:120/70R19

Rear:170/60R17

Verified Alternate Fitments

120/70R19 (F)

170/60R17 (R)

Alternate profiles verified for swingarm, chain guard, and fender clearances.

Final Drive Gearing & Speed/RPM Calculator

Shaft Drive

Factory reduction ratios, interactive sprocket gearing simulator, 6th gear cruising RPM matrix, and swingarm chain adjustment tolerances.

Shop Hypoid Gear Oils

Drive Architecture

Enclosed Cardan Bevel Shaft

Final Bevel Ratio

2.91 : 1

Hypoid Lubricant Spec

SAE 75W-90 Hypoid Gear Oil API GL-5

Bevel Oil Capacity

180 ml 75W-90 Hypoid GL-5

Drain / Fill Torque

20 N·m (14.8 ft-lb) with new aluminum crush ring

Drive Ratio & Torque Impact

Calculated Final RatioStock: 2.910

2.910 : 1

Drivetrain Torque Delta

OEM Factory Baseline Dynamics

Balanced all-around factory engineering calibrated for EPA emissions and street usability.

Cruising Engine RPM in 6th Gear

60 MPH

Stock: 3,281 RPM

3,281 RPM

70 MPH

Stock: 3,827 RPM

3,827 RPM

80 MPH

Stock: 4,374 RPM

4,374 RPM

Calculated using factory 6th gear ratio (0.848), primary reduction (1.65), and 170/60R17 rolling circumference.

Cardan Bevel Gear Maintenance

Hypoid Gear Oil Specification

SAE 75W-90 Hypoid Gear Oil API GL-5

Capacity: 180 ml 75W-90 Hypoid GL-5 (Fill to bottom threads of fill hole).

Drain Plug Torque

20 N·m (14.8 ft-lb) with new aluminum crush ring

Always renew aluminum crush ring to prevent final bevel housing leaks.

Inspect rubber gaiters / bellows and replace hypoid bevel oil every 12,000 miles

Recommended Fluid: Silkolene BOA 75W-90 Synthetic Hypoid Gear Oil

Shop Bevel Gear Oil Find Direct-Fit Gearing Sets

Factory Chassis Geometry

Chassis Alignment, Drive Tension & Rear Axle Calibration

Precision workshop alignment tools, dynamic drive tension tolerances, and axle spindle calibration for the 2016 BMW R 1200 GS.

Shaft Drive Architecture

Cardan Shaft Drive Bevel Gear Backlash & Hypoid Service

BEVEL GEAR BACKLASH INSPECTION:

0.15 - 0.25 mm (Wheel Rim Play)

Rotate rear wheel back and forth by hand on centerstand in neutral. Backlash play measured at wheel rim circumference should be subtle (1-2mm free play). Excessive play indicates pinion needle bearing wear.

HYPOID GEAR OIL & CRUSH RING SPEC:

SAE 75W-90 Hypoid Gear Oil API GL-5 (180 ml 75W-90 Hypoid GL-5)

Drain plug torque: 20 N·m (14.8 ft-lb) with new aluminum crush ring. Always clean magnetic drain plug of metallic sludge and replace the single-use aluminum crush ring to prevent final bevel housing leaks.

RUBBER GAITER & SPLINE LUBE:

Staburags NBU 30 PTM Lube

Inspect front and rear Paralever/Monolever rubber bellows for tears or water ingress. Lubricate drive shaft splines every 12,000 miles with heavy molybdenum disulphide paste.

Official NHTSA Safety Recalls & Technical Bulletins

2 Active Campaigns

U.S. Department of Transportation compliance database (Title 49 U.S.C. Chapter 301).

Verify VIN on NHTSA.gov

The U.S. National Highway Traffic Safety Administration reports 2 safety recall campaigns associated with this platform. Independent repair shops and riders should confirm that authorized dealership warranty remedies have been applied.

NHTSA #14V211000POWER TRAIN:MANUAL TRANSMISSION

Received: 18/04/2014▼

Defect Description

BMW of North America, LLC (BMW) is recalling certain model year 2013 R 1200 GS motorcycles manufactured November 2012 through August 2013. Pressure inside the transmission may cause the transmission output seal to be pushed out of place.

Safety Hazard / Consequence

If the output seal ring is pushed out of its proper position, oil may leak from the transmission onto the rear tire, increasing the risk of a crash.

Factory Remedy & Repair Action

BMW will notify owners, and dealers will fit a bracket to prevent the transmission seal from being pushed out of position, free of charge. The recall began on June 17, 2014. Owners may contact BMW customer service at 1-800-525-7417.

Manufacturer Notes: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

NHTSA #21V060000FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP

Received: 08/02/2021▼