Dedicated Subsystem WorkbenchPlatform Gen: 2015–2026

2018 Yamaha YZF-R3 Cylinder Compression & Leakdown Diagnostic Engine

Factory compression specs for 2018 Yamaha YZF-R3: standard pressure 165 - 210 PSI (1138 - 1448 kPa), service limit 142 PSI, dry vs wet test diagnostics and acoustic leak stethoscope.

Technical PassportOEM VERIFIED

Engine

321cc

Cooling

Liquid-Cooled

Final Drive

520 Chain

Engine Oil

2.10 L (2.22 US qt)

Spark Plug

NGK CR8E

Front Tire

110/70-17

Gen 2015–2026

Factory Platform Compatibility: All workshop fluid capacities, maintenance milestones, torque specifications, and consumables on this specification sheet are factory-identical across model years 2015 through 2026.

SPECS-TO-CART BUNDLESFactory Direct-Fit Maintenance Bundles Available

1-Click verified Motul engine oil service kits, race filters, spark plugs, and brake fluid pre-measured for this 2018 Yamaha YZF-R3.

Configure Service Bundles→

Select Model Year:(Active: 2018)
12 Production Years (2015–2026)

2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026

Suggested Items4 Verified Workshop Consumables Available for this Job

View Suggested Items ↓

Cylinder Compression & Leakdown Diagnostic Engine

Multi-Cylinder Dry vs. Wet Test Bench, Differential Pressure Regulator & Acoustic Stethoscope Locator

Ratio: 11.5:1Std: 165-210 PSILimit: 142 PSIWhip Adapter: M10 x 1.0

Diagnostic Presets:

Cyl #1 (Left)IN-SPEC

194PSI(1338 kPa)

Cyl #2 (Right)IN-SPEC

192PSI(1324 kPa)

Cross-Cylinder Variance: Δ 2 PSI (OEM Limit: ≤ 14 PSI)

VARIANCE IN-SPEC

All cylinders demonstrate strong, balanced mechanical sealing. Piston ring packs, cylinder cross-hatch, and valve seats are within factory specification.

Official Workshop Manual Compression Test Protocol

Step 0 of 5 Completed

Step 1: Engine Operating Temperature

Run engine until coolant reaches 60°C - 80°C (140°F - 176°F). Cylinder expansion brings rings and pistons to true operating clearances.

Step 2: Spark Plug Removal & Port Clean

Blow compressed air around spark plug wells to eject grit, then remove all spark plugs. Thread in M10 x 1.0 whip adapter hand-tight with fresh O-ring.

Step 3: Wide-Open Throttle (WOT) Lock

Hold throttle grip fully wide open (or lock throttle bodies open) to eliminate intake butterfly vacuum restriction and ensure 100% volumetric cylinder filling.

Step 4: Battery Tender Voltage Stabilization

Connect a 12V shop battery tender or booster. Starter must sustain uninterrupted cranking speed (350 RPM) to build maximum dynamic stroke pressure.

Step 5: Crank 4-6 Compression Strokes

Engage starter until gauge needle ceases rising (typically 4 to 6 strokes). Record maximum peak pressure and compare against the OEM limits above.

Official NHTSA Safety Recalls & Technical Bulletins

2 Active Campaigns

U.S. Department of Transportation compliance database (Title 49 U.S.C. Chapter 301).

Verify VIN on NHTSA.gov

The U.S. National Highway Traffic Safety Administration reports 2 safety recall campaigns associated with this platform. Independent repair shops and riders should confirm that authorized dealership warranty remedies have been applied.

NHTSA #21V048000EQUIPMENT:OTHER:LABELS

Received: 03/02/2021▼

Defect Description

Yamaha Motor Corporation, USA (Yamaha) is recalling certain 2019-2021 YZF-R3 motorcycles, 2019-2020 XMAX (CDZ300) scooters, and 2020 MT03 motorcycles. The Vehicle Identification Number (VIN) printed on the Federal Certification label may not match the VIN stamped on the vehicle. As such, these vehicles fail to comply with the requirements of 49 CFR Part 567, "Certification."

Safety Hazard / Consequence

The owner, referencing an incorrect VIN label, may not recognize their vehicle is involved in a safety recall, and may not have the recall remedy performed, which could increase the risk of injury, fire or a crash.

Factory Remedy & Repair Action

Yamaha will notify owners, and dealers will install a correct certification label, free of charge. The recall began February 19, 2021. Owners may contact Yamaha customer service at 1-800-962-7926. Yamaha's number for this recall is 990144.

Manufacturer Notes: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

NHTSA #20V611000VISIBILITY

Received: 05/10/2020▼

OEM Workshop Archives

Official Factory Service Bulletins & Field Updates

1 Documented Bulletin

Bulletin #YAM-17V111Bulletin M2017-001R / Campaign 990112: YZF-R3 Fuel Tank Bracket & Main Ignition Switch

Source: Yamaha_YZFR3_Recall990112_FuelTankBracket.pdf

Mandated Torques:Torque: 1.2 N·m (0.12 m-kg, 10.6 in-lb) (Main Switch Torx T20 Retaining Screws - Do NOT overtighten)Torque: 100 N·m (Steering Stem Nut)

Consumable Specs:Vibration Damping Rubber GrommetsDielectric Grease

Genuine Part Numbers:90891-20291-001WD-H2501-02-00B04-H2501-01-001WD-F412Y-01-00LIT-11616-28-57

Chassis & Electrical ArchitectureExploded View: Fuel Tank Fitting Bracket & Main Ignition Switch (Recall 990112 / NHTSA 17V-111 & 17V-112)

1.2 N·m Torx (10.6 in-lb) • 100 N·m Stem Nut • Kit # 90891-20291-00

Click any bracket, switch, or torque node to inspect Recall 990112 specifications.

Inspection TargetRecall 990112 / M2017-001R

Revised Fuel Tank Fitting Front Bracket

Genuine OEM Part # 1WD-F412Y-01-00

Factory Mechanical Specification:7 N·m (5.1 ft-lb) Mounting Screws

RECALL 990112 COUNTERMEASURE: Re-engineered geometry with increased +5mm clearance gap between bracket flange and fuel tank wall to eliminate vibration contact wear permanently.

Interactive Assembly Nodes: