Dedicated Subsystem WorkbenchPlatform Gen: 2018–2024

2023 Honda Gold Wing (GL1800) Tire Sizes, Cold Pressures & Gearing Ratios

OEM tire sizes, front cold PSI (), rear cold PSI (), sprocket teeth count, final drive ratio, and chain pitch for 2023 Honda Gold Wing (GL1800).

Technical PassportOEM VERIFIED

Engine

1833cc

Cooling

Liquid-Cooled

Final Drive

Shaft Drive

Engine Oil

4.40 L (4.65 US qt) Manual / 4.60 L (4.86 US qt) DCT

Spark Plug

NGK BKR6E-11 / Denso K20PR-U11

Front Tire

130/70R18 (63H)

Gen 2018–2024

Factory Platform Compatibility: All workshop fluid capacities, maintenance milestones, torque specifications, and consumables on this specification sheet are factory-identical across model years 2018 through 2024.

SPECS-TO-CART BUNDLESFactory Direct-Fit Maintenance Bundles Available

1-Click verified Motul engine oil service kits, race filters, spark plugs, and brake fluid pre-measured for this 2023 Honda Gold Wing (GL1800).

Configure Service Bundles→

Select Model Year:(Active: 2023)
7 Production Years (2018–2024)

2018 2019 2020 2021 2022 2023 2024

Suggested Items3 Verified Workshop Consumables Available for this Job

View Suggested Items ↓

Tire Engineering & Multi-Scenario Pressure Matrix

ETRTO Validated

Inflation targets calibrated across operating modes, verified rim width ranges, and certified alternate sizes.

Shop Direct-Fit Tires

Multi-Scenario Inflation Pressures

Solo Street / CommutingCold Baseline

Front: Not Available

Rear: Not Available

Two-Up Passenger & LuggageMax Load

Front: Not Available

Rear: Not Available

Off-Highway / Terrain Pressure

Maintain OEM cold baseline for street transfers; adjust -2 to -4 PSI for loose terrain.

Rim Geometry & ETRTO Envelopes

Front Wheel

OEM Rim Width:Not Available

Permissible Envelope:Not Available

Rear Wheel

OEM Rim Width:Not Available

Permissible Envelope:Not Available

Operating outside ETRTO envelope width alters crown radius, accelerates shoulder wear, and impacts lean stability.

Factory Dimensions & Verified Alternates

Factory Standard Sizes

Front:130/70R18 (63H)

Rear:200/55R16 (77H)

Shop In-Stock Matched 2-Tire Sets→

Verified Alternate Fitments

Factory standard sizing recommended.

Alternate profiles verified for swingarm, chain guard, and fender clearances.

Final Drive Gearing & Speed/RPM Calculator

Shaft Drive

Factory reduction ratios, interactive sprocket gearing simulator, 6th gear cruising RPM matrix, and swingarm chain adjustment tolerances.

Launch Full Gearing Simulator Shop Hypoid Gear Oils

Drive Architecture

Enclosed Cardan Bevel Shaft

Final Bevel Ratio

2.615 : 1

Hypoid Lubricant Spec

Not Available

Bevel Oil Capacity

Drain / Fill Torque

Drive Ratio & Torque Impact

Calculated Final RatioStock: 2.615

2.615 : 1

Drivetrain Torque Delta

OEM Factory Baseline Dynamics

Balanced all-around factory engineering calibrated for EPA emissions and street usability.

Cruising Engine RPM in 6th Gear

60 MPH

Stock: 3,318 RPM

3,318 RPM

70 MPH

Stock: 3,871 RPM

3,871 RPM

80 MPH

Stock: 4,424 RPM

4,424 RPM

Calculated using factory 6th gear ratio (0.923), primary reduction (1.681), and 200/55R16 (77H) rolling circumference.

Cardan Bevel Gear Maintenance

Hypoid Gear Oil Specification

Capacity: (Fill to bottom threads of fill hole).

Drain Plug Torque

Always renew aluminum crush ring to prevent final bevel housing leaks.

Inspect shaft splines and replace hypoid bevel oil every 12,000 miles (20,000 km)

Recommended Fluid:

Shop Bevel Gear Oil Find Direct-Fit Gearing Sets

Factory Chassis Geometry

Chassis Alignment, Drive Tension & Rear Axle Calibration

Precision workshop alignment tools, dynamic drive tension tolerances, and axle spindle calibration for the 2023 Honda Gold Wing (GL1800).

Shaft Drive Architecture

Cardan Shaft Drive Bevel Gear Backlash & Hypoid Service

BEVEL GEAR BACKLASH INSPECTION:

0.15 - 0.25 mm (Wheel Rim Play)

Rotate rear wheel back and forth by hand on centerstand in neutral. Backlash play measured at wheel rim circumference should be subtle (1-2mm free play). Excessive play indicates pinion needle bearing wear.

HYPOID GEAR OIL & CRUSH RING SPEC:

()

Drain plug torque: . Always clean magnetic drain plug of metallic sludge and replace the single-use aluminum crush ring to prevent final bevel housing leaks.

RUBBER GAITER & SPLINE LUBE:

Staburags NBU 30 PTM Lube

Inspect front and rear Paralever/Monolever rubber bellows for tears or water ingress. Lubricate drive shaft splines every 12,000 miles with heavy molybdenum disulphide paste.

Official NHTSA Safety Recalls & Technical Bulletins

0 Open Campaigns (Clean)

U.S. Department of Transportation compliance database (Title 49 U.S.C. Chapter 301).

Verify VIN on NHTSA.gov

No Active Federal Safety Recalls Reported

The U.S. DOT National Highway Traffic Safety Administration (NHTSA) records zero open safety recall campaigns for the 2023 Honda Gold Wing (GL1800) platform. Always check your individual 17-digit VIN at an authorized dealership or via NHTSA.gov for individual recall completions.

Explore Other Subsystems for this 2023 Honda Gold Wing (GL1800)

Jump straight into dedicated factory specifications and interactive workshop diagnostic engines.

← Full Motorcycle Overview

Subsystem Guide/torques

Fastener Torques

Engine drain plug, axle spindles, caliper mounts, triple clamp pinch bolts & thread lubrication derating guide.

Open Dedicated Workbench →

Subsystem Guide/fluids

Fluids & Capacities

Oil: 4.40 L (4.65 US qt) Manual / 4.60 L (4.86 US qt) DCT • Coolant: 3.60 L (3.80 US qt) 50/50 Pre-Mixed Ethylene Glycol • Brake: DOT 4 High-Temperature

Open Dedicated Workbench →

Subsystem Guide/fuses-relays