Dedicated Subsystem WorkbenchPlatform Gen: 2019–2024

2019 Honda CB500X / NX500 Throttle Body Synchronization & Fuel Delivery

Multi-cylinder vacuum sync specs, idle speed, EFI high-pressure fuel rail PSI, and injector resistance multimeter bench for 2019 Honda CB500X / NX500.

Gen 2019–2024

Factory Platform Compatibility: All workshop fluid capacities, maintenance milestones, torque specifications, and consumables on this specification sheet are factory-identical across model years 2019 through 2024.

Select Model Year:(Active: 2019)

2019 2020 2021 2022 2023 2024

Engine

471cc

Drive

520

Cooling

Liquid-Cooled

FSM Induction CalibrationParallel-Twin (180° Crank) (2 Throttle Bores)

Fuel Delivery, Throttle Body Synchronization & Manometer Balancer

Factory intake depression specifications (220 mmHg), electronic fuel pump pressure testing (43.5 PSI), injector resistance, and interactive multi-column manometer balancing.

Warm Idle: 1,150 - 1,250 RPM

Quick Workshop Diagnostic Presets

Simulate Throttle Linkage Asymmetry, Hunting Idle, or Intake Boot Vacuum Leaks

OPTIMAL SYNCHRONIZATION: BALANCED (Δ ≤ 10 mmHg)

Diagnostics:Max Differential: Δ 0 mmHg (Factory Max Tolerance: ≤ 10 mmHg)

All 2 throttle plates pull uniform intake depression within factory engineering tolerance (≤ 10 mmHg / 1.33 kPa). Delivers immediate linear throttle pickup, silky smooth idle, uniform cylinder torque pulses, and balanced exhaust temperatures.

Workshop Multi-Column Fluid Manometer

Damped intake depression columns. Target spec: 220 mmHg (±10 mmHg) at warm idle (1,150 - 1,250 RPM).

Reference: Cylinder #1 (Master Reference)

Mechanism: Bypass Screws

CYL #1

MASTER REF

220mmHg

29.3 kPa · 8.7 inHg

±0 mmHg (Exact Target)

Fixed Reference Master. Synchronize all slave throttle bodies to match this column.

CYL #2

SLAVE BORE

220mmHg

29.3 kPa · 8.7 inHg

±0 mmHg (Exact Target)

Vacuum Take-Off Ports: Intake insulator vacuum spigots with spring clips and rubber plugs

Damping Protocol: Restrictor valves must be adjusted until columns oscillate no more than ±5 mmHg per intake stroke.

Fuel Pump Pressure & 5-Min Hold Test

EFI Pressure Rail

Running Fuel Pressure

43.5 PSI(3.00 bar)

OEM Running Spec

43.5 PSI (±3 PSI)

PASS: WITHIN OEM RUNNING SPEC

Fuel pump delivery pressure is 43.5 PSI (Factory spec: 43.5 PSI ± 3 PSI / 3 bar). High-pressure regulator and pump rotor operating within factory design threshold.

Connect mechanical gauge to the quick-disconnect fuel rail fitting using an OEM banjo or T-adapter.

Fuel Injector Resistance & Induction Specs

Multimeter Bench Check

OEM Injector Solenoid Resistance

11.7 - 12.4 Ω at 20°C

Measure across injector 2-pin harness socket with ignition OFF. Internal coil resistance increases by ~0.4% per °C rise above 20°C (68°F). Replace injector if resistance reads open (> 100 kΩ) or shorted (< 2 Ω).

Bore Diameter

34 mm

Operating Temp

80°C (176°F)

Induction Type

PGM-FI Electronic Fuel Injection with 34mm Keihin Throttle Bodies

Injector O-rings must be lubricated with a light coat of clean engine oil before seating into fuel rail.

4-Step Throttle Body Synchronization Protocol

Official workshop manual step-by-step checklist. Mark each step as you complete it on the workbench.

0 of 4 Steps Complete

1CLICK TO MARK DONE

Engine Pre-Flight Conditioning

Check and adjust valve clearances to spec before attempting sync. Ensure air filter is clean, spark plugs are fresh, and engine is fully warmed to operating temperature (80°C–90°C).

2CLICK TO MARK DONE

Manometer Connection & Damping

Connect 2-column liquid or digital manometer hoses to Intake insulator vacuum spigots with spring clips and rubber plugs. Adjust in-line hose restrictor valves to dampen rapid intake pulsation until fluid columns stabilize.

3CLICK TO MARK DONE

Balance Screw Calibration

With engine idling at 1,150 - 1,250 RPM, identify Cylinder #1 (Master Reference). Adjust Center balance screw between Cylinders 1 and 2 with locknut until all cylinder columns are within 10 mmHg (1.33 kPa) of the master reference.

4CLICK TO MARK DONE

Throttle Blip & Locknut Verification

Blip throttle to 3,000 RPM 2–3 times and verify columns return evenly to idle balance. Tighten any balance screw locknuts securely, re-install rubber vacuum sealing caps, and verify idle speed.

Shop Carb & Throttle Body Cleaners→Shop Multi-Column Manometers & Sync Tools→Shop EFI Fuel Pressure Test Gauge Kits→

Official NHTSA Safety Recalls & Technical Bulletins

2 Active Campaigns

U.S. Department of Transportation compliance database (Title 49 U.S.C. Chapter 301).

Verify VIN on NHTSA.gov

The U.S. National Highway Traffic Safety Administration reports 2 safety recall campaigns associated with this platform. Independent repair shops and riders should confirm that authorized dealership warranty remedies have been applied.

NHTSA #21V382000EXTERIOR LIGHTING

Received: 24/05/2021▼

Defect Description

Honda (American Honda Motor Co.) is recalling certain 2020-2021 Super Cub C125, CB500X, CB650R, CBR300R, CBR500R, CBR650R, Rebel 300, Rebel 500, Monkey, 2020 CRF250L, GROM, 2021 CRF300L, and CB500F motorcycles. The rear reflector lens may not reflect brightly enough. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."

Safety Hazard / Consequence

A dim rear reflector may reduce the visibility of the motorcycle to other drivers, increasing the risk of a crash or injury.

Factory Remedy & Repair Action

Dealers will replace the rear reflector, free of charge. Owner notification letters were mailed July 7, 2021. Owners may contact Honda customer service at 1-866-784-1870. Honda's number for this recall is KM3.

Manufacturer Notes: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.

NHTSA #21V690000SERVICE BRAKES, HYDRAULIC

Received: 02/09/2021▼