Dedicated Subsystem WorkbenchPlatform Gen: 2020–2026

2024 Yamaha Tenere 700 Tire Sizes, Cold Pressures & Gearing Ratios

OEM tire sizes, front cold PSI (), rear cold PSI (), sprocket teeth count, final drive ratio, and chain pitch for 2024 Yamaha Tenere 700.

Gen 2020–2026

Factory Platform Compatibility: All workshop fluid capacities, maintenance milestones, torque specifications, and consumables on this specification sheet are factory-identical across model years 2020 through 2026.

Select Model Year:(Active: 2024)

2020 2021 2022 2023 2024 2025 2026

Engine

689cc

Drive

525

Cooling

Liquid-Cooled

Tire Engineering & Multi-Scenario Pressure Matrix

ETRTO Validated

Inflation targets calibrated across operating modes, verified rim width ranges, and certified alternate sizes.

Shop Direct-Fit Tires

Multi-Scenario Inflation Pressures

Solo Street / CommutingCold Baseline

Front: 32 PSI

Rear: 36 PSI

Two-Up Passenger & LuggageMax Load

Front: 34 PSI

Rear: 42 PSI

Off-Highway / Terrain Pressure

Maintain OEM cold baseline for street transfers; adjust -2 to -4 PSI for loose terrain.

Rim Geometry & ETRTO Envelopes

Front Wheel

OEM Rim Width:2.15"

Permissible Envelope:2.15" - 2.50"

Rear Wheel

OEM Rim Width:4.00"

Permissible Envelope:4.00" - 4.50"

Operating outside ETRTO envelope width alters crown radius, accelerates shoulder wear, and impacts lean stability.

Factory Dimensions & Verified Alternates

Factory Standard Sizes

Front:90/90-21

Rear:150/70R18

Verified Alternate Fitments

90/90-21 (F)

150/70R18 (R)

Alternate profiles verified for swingarm, chain guard, and fender clearances.

Final Drive Gearing & Speed/RPM Calculator

Chain Drive

Factory reduction ratios, interactive sprocket gearing simulator, 6th gear cruising RPM matrix, and swingarm chain adjustment tolerances.

Shop Chains & Sprockets

Factory Pitch / Size

525 Pitch

OEM Sprockets

15T Front / 46T Rear

Factory Final Ratio

3.067 : 1

Factory Link Count

122 Links (Rivet)

Tensile Rating

8,400 lbs

Quick Gearing Presets

Front Countershaft SprocketStock: 15T

15 Teeth

Factory teeth count

Rear Driven SprocketStock: 46T

46 Teeth

Factory teeth count

Drive Ratio & Torque Impact

Calculated Final RatioStock: 3.067

3.067 : 1-0.01%

Drivetrain Torque Delta

0.0% Taller Gearing (Reduced Highway RPM)

Lengthens transmission gears, lowers sustained engine RPM on motorways, and reduces engine buzz and vibration.

Countershaft Speedo Variance:+0.0%

At 70.0 mph indicated speed, true vehicle ground speed is 70.0 mph.

Cruising Engine RPM in 6th Gear

60 MPH

Stock: 3,862 RPM

3,862 RPM

70 MPH

Stock: 4,506 RPM

4,505 RPM

-1 RPM

80 MPH

Stock: 5,150 RPM

5,149 RPM

-1 RPM

Calculated using factory 6th gear ratio (0.852), primary reduction (1.925), and 150/70R18 rolling circumference.

Chain Sizing & Swingarm Slack

Recommended Drive Chain Length:122 Links

Fits within factory swingarm axle slot adjustment range (35 - 45 mm (1.4 - 1.8 in) on side stand). Retain stock 122 links.

Factory Swingarm Slack Tolerance

35 - 45 mm (1.4 - 1.8 in) on side stand

Measure slack at midpoint between countershaft and rear axle on the bottom strand with the motorcycle on its side stand unladen.

Master Link Requirement:Rivet link (ZJ) mandatory for > 400cc

Recommended Hardware: D.I.D 525 VX3 Pro-Street X-Ring Chain (122 Links) • Sunstar Steel Countershaft (15T) & Rear Sprocket (46T)

Shop Chain Breaker & Rivet Tools Find Direct-Fit Gearing Sets

Factory Chassis Geometry

Chassis Alignment, Drive Tension & Rear Axle Calibration

Precision workshop alignment tools, dynamic drive tension tolerances, and axle spindle calibration for the 2024 Yamaha Tenere 700.

Factory Swingarm Slack Tolerance

35 - 45 mm (1.4 - 1.8 in) on side stand

Test Condition: Measure midway on lower chain run with bike on side stand (unweighted).

Measured Chain Slack

40 mm

10mm (Too Tight)Factory Window: 35 - 45 mm65mm (Critical Slack)

PASS: IN FACTORY SPEC(40 mm / 1.57 in)

FACTORY TOLERANCE CERTIFIED: Chain tension is in optimal balance. Allows complete swingarm articulation through the entire suspension stroke without countershaft binding or excessive snatch on deceleration.

Precision Alignment

Rear Axle Caliper Alignment

Why mechanics never trust swingarm stamped notches: Factory stamping tolerances can be off by up to 3mm, causing the rear tire to "dog-track" and chew through tire shoulders.

LEFT PIVOT TO AXLE:

215.0 mm

RIGHT PIVOT TO AXLE:

215.0 mm

PERFECT WHEEL ALIGNMENT (PASS)Δ 0.0 mm

Rear axle is square to the swingarm pivot within 0.5mm. Sprocket and chain tracking run in direct true plane.

Wear Limit Diagnostic

21-Pin (20-Pitch) Chain Stretch Test

Pull chain tight and measure distance across 21 consecutive pins with a vernier caliper. Standard new length = 317.5 mm; factory discard limit = 323.0 mm (1.5% stretch).

MEASURED 21-PIN DISTANCE:

317.5 mm

Stretch: +0.0 mm (0.0%)

Remaining Chain Pin/Bushing Life:100% (GOOD)

Three Professional Workshop Alignment Techniques

Method 1 — Swingarm Pivot to Axle Center (The Gold Standard):

Insert a precision rod or vernier caliper measuring from the center dimple of the swingarm pivot bolt to the center dimple of the rear axle on both left and right sides. Both sides must match within 0.5 mm. This mechanically guarantees that the rear axle is perfectly perpendicular to the motorcycle chassis centerline regardless of factory swingarm stamping defects.

Six-Step Workshop Chain Adjustment Protocol

Rear Axle Nut: 150 N·mAdjuster Locknut: 16 - 22 N·m

1Loosen Axle Spindle Nut

Loosen the rear axle nut 1 to 2 full turns (150 N·m). Keep it snug enough so the wheel does not cock sideways freely.

2Back Off Adjuster Locknuts

Back off the jam locknuts on both the left and right adjuster bolts by 2 to 3 turns using a 12mm or 14mm box wrench.

3Turn Adjusters in Small Increments

Turn both adjuster bolts equally. One full 360° turn of an M8 bolt moves the axle by 1.25 mm. Adjust 1/4-turn at a time.

4Kick Tire Firmly Forward

Kick the rear tire firmly toward the front of the motorcycle to ensure the axle blocks are solidly seated against the bolt heads.

5Torque Rear Axle Nut to Spec

Torque the axle spindle nut to exactly 150 N·m. Always use a calibrated 1/2" torque wrench.

6Crucial Re-Check of Slack

Torquing down the rear axle nut frequently tightens chain slack by 2 to 4 mm! Always re-check slack after full torque is applied.

Official NHTSA Safety Recalls & Technical Bulletins

0 Open Campaigns (Clean)

U.S. Department of Transportation compliance database (Title 49 U.S.C. Chapter 301).

Verify VIN on NHTSA.gov

No Active Federal Safety Recalls Reported

The U.S. DOT National Highway Traffic Safety Administration (NHTSA) records zero open safety recall campaigns for the 2024 Yamaha Tenere 700 platform. Always check your individual 17-digit VIN at an authorized dealership or via NHTSA.gov for individual recall completions.