Dedicated Subsystem WorkbenchPlatform Gen: 2014–2020

2019 Yamaha MT-09 Throttle Body Synchronization & Fuel Delivery

Multi-cylinder vacuum sync specs, idle speed, EFI high-pressure fuel rail PSI, and injector resistance multimeter bench for 2019 Yamaha MT-09.

Gen 2014–2020

Factory Platform Compatibility: All workshop fluid capacities, maintenance milestones, torque specifications, and consumables on this specification sheet are factory-identical across model years 2014 through 2020.

Select Model Year:(Active: 2019)

2014 2015 2016 2017 2018 2019 2020

Engine

847cc

Drive

525

Cooling

Liquid-Cooled

FSM Induction CalibrationInline-3 (3 Throttle Bores)

Fuel Delivery, Throttle Body Synchronization & Manometer Balancer

Factory intake depression specifications (230 mmHg), electronic fuel pump pressure testing (47 PSI), injector resistance, and interactive multi-column manometer balancing.

Warm Idle: 1,150 - 1,250 RPM

Quick Workshop Diagnostic Presets

Simulate Throttle Linkage Asymmetry, Hunting Idle, or Intake Boot Vacuum Leaks

OPTIMAL SYNCHRONIZATION: BALANCED (Δ ≤ 10 mmHg)

Diagnostics:Max Differential: Δ 0 mmHg (Factory Max Tolerance: ≤ 10 mmHg)

All 3 throttle plates pull uniform intake depression within factory engineering tolerance (≤ 10 mmHg / 1.33 kPa). Delivers immediate linear throttle pickup, silky smooth idle, uniform cylinder torque pulses, and balanced exhaust temperatures.

Workshop Multi-Column Fluid Manometer

Damped intake depression columns. Target spec: 230 mmHg (±10 mmHg) at warm idle (1,150 - 1,250 RPM).

Reference: Cylinder #1 (Fixed Reference - Do Not Adjust)

Mechanism: Bypass Screws

CYL #1

MASTER REF

230mmHg

30.7 kPa · 9.1 inHg

±0 mmHg (Exact Target)

Fixed Reference Master. Synchronize all slave throttle bodies to match this column.

CYL #2

SLAVE BORE

230mmHg

30.7 kPa · 9.1 inHg

±0 mmHg (Exact Target)

CYL #3

SLAVE BORE

230mmHg

30.7 kPa · 9.1 inHg

±0 mmHg (Exact Target)

Vacuum Take-Off Ports: M5 threaded intake spigot nipples with rubber sealing caps below throttle body clamps

Damping Protocol: Restrictor valves must be adjusted until columns oscillate no more than ±5 mmHg per intake stroke.

Fuel Pump Pressure & 5-Min Hold Test

EFI Pressure Rail

Running Fuel Pressure

47 PSI(3.24 bar)

OEM Running Spec

47 PSI (±3 PSI)

PASS: WITHIN OEM RUNNING SPEC

Fuel pump delivery pressure is 47 PSI (Factory spec: 47 PSI ± 3 PSI / 3.24 bar). High-pressure regulator and pump rotor operating within factory design threshold.

Connect mechanical gauge to the quick-disconnect fuel rail fitting using an OEM banjo or T-adapter.

Fuel Injector Resistance & Induction Specs

Multimeter Bench Check

OEM Injector Solenoid Resistance

12.0 - 12.4 Ω at 20°C

Measure across injector 2-pin harness socket with ignition OFF. Internal coil resistance increases by ~0.4% per °C rise above 20°C (68°F). Replace injector if resistance reads open (> 100 kΩ) or shorted (< 2 Ω).

Bore Diameter

41 mm

Operating Temp

80°C (176°F)

Induction Type

Electronic Fuel Injection with YCC-T Ride-by-Wire & Mikuni Throttle Bodies

Injector O-rings must be lubricated with a light coat of clean engine oil before seating into fuel rail.

4-Step Throttle Body Synchronization Protocol

Official workshop manual step-by-step checklist. Mark each step as you complete it on the workbench.

0 of 4 Steps Complete

1CLICK TO MARK DONE

Engine Pre-Flight Conditioning

Check and adjust valve clearances to spec before attempting sync. Ensure air filter is clean, spark plugs are fresh, and engine is fully warmed to operating temperature (80°C–90°C).

2CLICK TO MARK DONE

Manometer Connection & Damping

Connect 3-column liquid or digital manometer hoses to M5 threaded intake spigot nipples with rubber sealing caps below throttle body clamps. Adjust in-line hose restrictor valves to dampen rapid intake pulsation until fluid columns stabilize.

3CLICK TO MARK DONE

Balance Screw Calibration

With engine idling at 1,150 - 1,250 RPM, identify Cylinder #1 (Fixed Reference - Do Not Adjust). Adjust Individual brass air bypass screws on Cylinder #2 and Cylinder #3 throttle bodies until all cylinder columns are within 10 mmHg (1.33 kPa) of the master reference.

4CLICK TO MARK DONE

Throttle Blip & Locknut Verification

Blip throttle to 3,000 RPM 2–3 times and verify columns return evenly to idle balance. Tighten any balance screw locknuts securely, re-install rubber vacuum sealing caps, and verify idle speed.

Shop Carb & Throttle Body Cleaners→Shop Multi-Column Manometers & Sync Tools→Shop EFI Fuel Pressure Test Gauge Kits→

Official NHTSA Safety Recalls & Technical Bulletins

1 Active Campaign

U.S. Department of Transportation compliance database (Title 49 U.S.C. Chapter 301).

Verify VIN on NHTSA.gov

The U.S. National Highway Traffic Safety Administration reports 1 safety recall campaign associated with this platform. Independent repair shops and riders should confirm that authorized dealership warranty remedies have been applied.

NHTSA #22V130000DO NOT OPERATE / PARK OUTSIDEENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE

Received: 07/03/2022▼

Defect Description

Yamaha Motor Corporation, USA (Yamaha) is recalling certain 2021-2022 MT-09, MT-09 SP, and MTT9GT (Tracer 9 GT) motorcycles. Improper electronic control unit (ECU) programming may limit the throttle response, cause an engine stall, or fail to illuminate the engine warning light when a system error occurs.

Safety Hazard / Consequence

Limited throttle response, engine stall, or a missing warning light can increase the risk of a crash.

Factory Remedy & Repair Action

Owners should not operate their motorcycle, other than to take it to a dealer, until the remedy is performed. Dealers will reprogram the ECU, free of charge. Owner notification letters were mailed March 17, 2022. Owners may contact Yamaha customer service at 1-866-894-1626. Yamaha's number for this recall is 990158.

Manufacturer Notes: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.