Dedicated Subsystem WorkbenchPlatform Gen: 2017–2024

2019 KTM 390 Duke Cylinder Compression & Leakdown Diagnostic Engine

Factory compression specs for 2019 KTM 390 Duke: standard pressure 165 - 205 PSI (1138 - 1413 kPa), service limit 135 PSI, dry vs wet test diagnostics and acoustic leak stethoscope.

Gen 2017–2024

Factory Platform Compatibility: All workshop fluid capacities, maintenance milestones, torque specifications, and consumables on this specification sheet are factory-identical across model years 2017 through 2024.

Select Model Year:(Active: 2019)

2017 2018 2019 2020 2021 2022 2023 2024

Engine

373cc

Drive

520

Cooling

Liquid-Cooled

Cylinder Compression & Leakdown Diagnostic Engine

Multi-Cylinder Dry vs. Wet Test Bench, Differential Pressure Regulator & Acoustic Stethoscope Locator

Ratio: 12.6:1Std: 165-205 PSILimit: 135 PSIWhip Adapter: M12 x 1.25

Centrifugal Exhaust Cam Auto-Decomp Weight

CRITICAL THUMPER NOTE: Engine features Centrifugal Exhaust Cam Auto-Decomp Weight. At cranking speed (< 400 RPM), the decompressor holds an exhaust valve slightly cracked open. Normal cranking reading with active decompressor is 85 - 105 PSI. To verify true full cylinder compression (165-205 PSI), either temporarily deactivate the decompressor pin or verify via 100 PSI leakdown testing at TDC.

Diagnostic Presets:

Cylinder #1 (Single)IN-SPEC

191PSI(1317 kPa)

Single Cylinder Pressure: 191 PSI (Service Limit: ≥ 135 PSI)

All cylinders demonstrate strong, balanced mechanical sealing. Piston ring packs, cylinder cross-hatch, and valve seats are within factory specification.

Official Workshop Manual Compression Test Protocol

Step 0 of 5 Completed

Step 1: Engine Operating Temperature

Run engine until coolant reaches 60°C - 80°C (140°F - 176°F). Cylinder expansion brings rings and pistons to true operating clearances.

Step 2: Spark Plug Removal & Port Clean

Blow compressed air around spark plug wells to eject grit, then remove all spark plugs. Thread in M12 x 1.25 whip adapter hand-tight with fresh O-ring.

Step 3: Wide-Open Throttle (WOT) Lock

Hold throttle grip fully wide open (or lock throttle bodies open) to eliminate intake butterfly vacuum restriction and ensure 100% volumetric cylinder filling.

Step 4: Battery Tender Voltage Stabilization

Connect a 12V shop battery tender or booster. Starter must sustain uninterrupted cranking speed (350 RPM) to build maximum dynamic stroke pressure.

Step 5: Crank 4-6 Compression Strokes

Engage starter until gauge needle ceases rising (typically 4 to 6 strokes). Record maximum peak pressure and compare against the OEM limits above.

Official NHTSA Safety Recalls & Technical Bulletins

2 Active Campaigns

U.S. Department of Transportation compliance database (Title 49 U.S.C. Chapter 301).

Verify VIN on NHTSA.gov

The U.S. National Highway Traffic Safety Administration reports 2 safety recall campaigns associated with this platform. Independent repair shops and riders should confirm that authorized dealership warranty remedies have been applied.

NHTSA #25V740000FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP

Received: 30/10/2025▼

Defect Description

KTM North America, Inc. is recalling certain 2024 390 Duke, 250 Duke, 990 Duke, Husqvarna Vitpilen 401, and Husqvarna Svartpilen 401 motorcycles. The seal on the fuel filler cap may develop cracks and leak fuel.

Safety Hazard / Consequence

A fuel leak increases the risk of fire or injury.

Factory Remedy & Repair Action

Dealers will inspect and replace the fuel cap gasket, free of charge. Owner notification letters were mailed December 15, 2025. Owners may contact KTM customer service at 1-888-985-6090. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov March 31, 2026.

NHTSA #25V825000ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE

Received: 01/12/2025▼